Statement on the procurement policy for conflict-free metals
Conflict metals refer to rare metals such as gold (Au), tantalum (Ta), tungsten (W), cobalt (Co) and tin (Sn), which come from the Congo and surrounding countries and regions, non-governmental military groups or illegal military Mining areas in conflict areas controlled by factions. The illegal mining profits obtained by local military groups were stolen from citizens and caused human rights violations and environmental degradation in the Congo and surrounding countries and regions.
Taikang does not use "conflict minerals" from Congo and its surrounding countries and regions. It only purchases materials from environmentally and socially responsible raw material suppliers, and requires our raw material suppliers to conduct business with their supply chains in a reasonable manner. Due diligence to ensure that the metals used in the raw materials provided to Taikang did not come from conflict areas.
Statement on the procurement policy for conflict-free metals
Conflict metals refer to rare metals such as gold (Au), tantalum (Ta), tungsten (W), cobalt (Co) and tin (Sn), which come from the Congo and surrounding countries and regions, non-governmental military groups or illegal military Mining areas in conflict areas controlled by factions. The illegal mining profits obtained by local military groups were stolen from citizens and caused human rights violations and environmental degradation in the Congo and surrounding countries and regions.
Taikang does not use "conflict minerals" from Congo and its surrounding countries and regions. It only purchases materials from environmentally and socially responsible raw material suppliers, and requires our raw material suppliers to conduct business with their supply chains in a reasonable manner. Due diligence to ensure that the metals used in the raw materials provided to Taikang did not come from conflict areas.
Teconn tell you the cause of electronic connector damage which?
Teconn tell you the cause of electronic connector damage which?
(1) electrical connection line or clip is not enough to burn the stock or broken.
(2) electric connection line scattered stock is serious, be burned off the stock or burn line.
(3) serious corrosion of the electrical connection, resulting in cross-section flow is not enough to be burned strand or burning line.
(4) electrical connection with the clamp or bad contact with the contact line contact with the bad line, resulting in burning.
(5) clip and clue contact carrier surface is not enough, resulting in burning.
(6) loosening of a clamp nut is not found and dealt with in time, resulting in loss of electronic connectors.
(7) No temperature change after electronic connector mounting Offset or too little offset.
(8) After the installation of electronic connectors offset the value of the larger deviation, the bearing cable and the contact line between the vertical electrical connection line relaxation, to relaxation to the lower part of the contact line, was in operation in the pantograph to fight Bad or cut off. Vertical part of the bottom circle and the contact line spacing is too small, pantograph bad or cut bad.
(9) contact line power supply clip clip installed skewed by the pantograph, which led to cut bow accident.
(10) Occur in other locations of the catenary bow, pantograph to continue to run to the electronic connector installation, the electronic connector cut bad.
(1) electrical connection line or clip is not enough to burn the stock or broken.
(2) electric connection line scattered stock is serious, be burned off the stock or burn line.
(3) serious corrosion of the electrical connection, resulting in cross-section flow is not enough to be burned strand or burning line.
(4) electrical connection with the clamp or bad contact with the contact line contact with the bad line, resulting in burning.
(5) clip and clue contact carrier surface is not enough, resulting in burning.
(6) loosening of a clamp nut is not found and dealt with in time, resulting in loss of electronic connectors.
(7) No temperature change after electronic connector mounting Offset or too little offset.
(8) After the installation of electronic connectors offset the value of the larger deviation, the bearing cable and the contact line between the vertical electrical connection line relaxation, to relaxation to the lower part of the contact line, was in operation in the pantograph to fight Bad or cut off. Vertical part of the bottom circle and the contact line spacing is too small, pantograph bad or cut bad.
(9) contact line power supply clip clip installed skewed by the pantograph, which led to cut bow accident.
(10) Occur in other locations of the catenary bow, pantograph to continue to run to the electronic connector installation, the electronic connector cut bad.
Subscribe to our newsletter.
Subscribe to our newsletter.
Nostrud amet eu ullamco nisi aute in ad minim nostrud adipisicing velit quis. Duis tempor incididunt dolore.
Contact Us
Weekly articles
Weekly articles
No spam
No spam
Non laboris consequat cupidatat laborum magna. Eiusmod non irure cupidatat duis commodo amet.
Officia excepteur ullamco ut sint duis proident non adipisicing. Voluptate incididunt anim.
